好日子论坛

以后地位:好日子论坛 > 消息中间 > 行业消息
行业消息
  • 点焊机掩护注重事变
  • 本站编辑:好日子论坛 宣布日期:2018-10-18 19:11 阅读次数:
  1、点焊机操纵职员不得以身材任何部位或任何物件接近触摸传动的齿轮、传动槽轮、链轮、皮带、链条、调直机、感到体、接近开关和电柜内、变压器等带有风险电压的导体局部。                                                       
 
2、点焊机操纵职员不得把手或物体接近正在加压活动的上电极或放入上、下电极之间。
 
3、点焊机操纵职员不得带电插或碰掉焊网电源变压器上的功率调理插把,不得掀起防护板。4、点焊机操纵职员不得拆掉、碰断主机和电控柜上的接零(接地)宁静掩护线,按期查抄接零(接地)宁静掩护线是不是杰出。
 
5、当点焊电机控柜内有熔断时,应先停机停电,由电工查出熔断缘由以后,再以不异型号规格的熔芯改换,不然将引发火警和销毁器件。
 
6、点焊机操纵职员不得随便调剂电控柜内的器件,不得随便把东西、铁丝等杂物放入电控柜或放在机箱顶部和齿条上。
 
7、点焊机操纵职员必须实时对轴承、滑块、滑道、滑套、链轮、链条、齿轮、齿条等转动磨擦的零部件加注光滑油,不得缺油运转。加注光滑油应在停机落后行。必须在运转中加
 
 
注光滑油的部位,不得以加油用具碰触运转中的机构,可接纳滴注体例。
1. The operator of spot welder shall not touch any part of the body or any object near the transmission gear, transmission groove wheel, sprocket wheel, belt, chain, straightening machine, induction body, proximity switch, electric cabinet, transformer and other conductor parts with dangerous voltage.
 
 
 
2. The operator of spot welder shall not put his hand or object near the upper electrode which is moving under pressure or put it between the upper and lower electrodes.
 
 
 
3. The operator of the spot welder shall not plug or touch the power adjustment plug on the power transformer of the welding mesh, and shall not lift the protection plate. 4. The operator of spot welder shall not remove or break the safety wire connecting zero (ground) on the main machine and electric control cabinet, and regularly check whether the safety wire connecting zero (ground) is in good condition.
 
 
 
5. When there is a fuse break in the mechanical and electrical control cabinet of spot welding, the machine should be shut down and power cut first. After the electrician finds out the cause of the fuse break, the core of the same model and specification should be replaced.
 
 
 
6. The operator of spot welder shall not randomly adjust the components in the electric control cabinet, and shall not randomly put the tools, wire and other sundry objects into the electric control cabinet or on the top of the machine case and rack.
 
 
 
7. The operator of spot welding machine must fill lubricating oil for the rolling friction parts such as bearings, sliders, slideways, sliding sleeves, sprockets, chains, gears and rack in time, and must not run short of oil. Lubricating oil filling shall be carried out after shutdown. Must be added in operation
 
 
 
 
 
The place where lubricating oil is poured shall not be touched by the oiler with the running mechanism, but by drip.